Power Transmission
-
Tractor Belt Pulley 20 Inch Double Groove B Section - 1 Pcs PackThe function of the pulley is to transmit power from the tractor to stationary machinery by means of a belt. It is used to operate thresher, centrifugal pump, silage cutter, and several other machinery. The pulley is located either on the left , right or rear side of the tractor. --> FREE SHIPPING <-- ₹ 4423.00 + 18% GST = ₹ 5219.00 Learn More₹4,423.00 -
Shaft Mounted Speed Reducer H Type Gear Box StandardWe are offering SMSR Gearboxes in six different sizes (C, D, E, F, G & H) with three ratios of 5:1, 13:1, & 20:1. The gears are helical type and are manufactured on CNC machines and are case hardened with a hard wear layer and a softer core so as to resist shock loads. The Shaft Mounted Speed Reducer Gearboxes are facilitated with metallic double lip oil seals. This help blocks out the dirt from the outside atmosphere. All gears are fully tested for gear cracks, noise, and leaks for a trouble-free operation. The gear units have an advanced tooth design to give higher power and torque. --> FREE SHIPPING <-- ₹ 56380.00 + 18% GST = ₹ 66528.00 Learn More₹56,380.00 -
Shaft Mounted Speed Reducer G Type Gear Box Hold BackWe are offering SMSR Gearboxes in six different sizes (C, D, E, F, G & H) with three ratios of 5:1, 13:1, & 20:1. The gears are helical type and are manufactured on CNC machines and are case hardened with a hard wear layer and a softer core so as to resist shock loads. The Shaft Mounted Speed Reducer Gearboxes are facilitated with metallic double lip oil seals. This help blocks out the dirt from the outside atmosphere. All gears are fully tested for gear cracks, noise, and leaks for a trouble-free operation. The gear units have an advanced tooth design to give higher power and torque. --> FREE SHIPPING <-- ₹ 42231.00 + 18% GST = ₹ 49832.00 Learn More₹42,231.00 -
Worm Gear Box Horizontal Drive with Double Output Shaft CU-HThe Worm Gear Box reduction ratio is determined by the number of starts of the worm and number of teeth on the worm gear.Worm gear sets are used to transmit power between non-parallel, non-intersecting shafts, usually having a shaft angle of 90 degrees. The direction of rotation of the worm wheel depends upon the direction of rotation of the worm, and whether the worm teeth are cut in a left-hand or right-hand direction.However right hand worm and worm gear sets are considered standard. --> FREE SHIPPING <-- Learn More₹8,652.00 -
Worm Gear Box Vertical Output Drive CU-VThe Worm Gear Box reduction ratio is determined by the number of starts of the worm and number of teeth on the worm gear.Worm gear sets are used to transmit power between non-parallel, non-intersecting shafts, usually having a shaft angle of 90 degrees. The direction of rotation of the worm wheel depends upon the direction of rotation of the worm, and whether the worm teeth are cut in a left-hand or right-hand direction.However right hand worm and worm gear sets are considered standard. --> FREE SHIPPING <-- Learn More₹9,012.00 -
V Belt Pulley Single Groove A and B Section 2 to 6 InchesA Pulley is a mechanism composed of a wheel on an axle or shaft that may have a groove between two flanges around its circumference. A rope, cable, belt, or chain usually runs over the wheel and inside the groove, if present Pulleys are used to change the direction of an applied force, transmit rotational motion or realize a mechanical advantage in either a linear or rotational system of motion. Learn More₹635.00 -
V Belt Pulley Double Groove A and B Section 2 to 6 InchesA Pulley is a mechanism composed of a wheel on an axle or shaft that may have a groove between two flanges around its circumference. A rope, cable, belt, or chain usually runs over the wheel and inside the groove, if present Pulleys are used to change the direction of an applied force, transmit rotational motion or realize a mechanical advantage in either a linear or rotational system of motion. Learn More₹427.00 -
-67%Bharat Bijlee 3 Phase 150 HP 1500 RPM 4 Pole Crane & Hoist Duty MotorFrame 160 is with Cast Iron Body and Terminal Box position on Top. Frames 180 to 225 are with Cast Iron body and Terminal Box position on RHS. On request terminal box can be given on Top/LHS position. Frames 250 and above are with Cast Iron body and Terminal Box position on Top On request terminal box can be given with RHS/LHS position. CRANE & HOIST DUTY MOTORS -- Specifications :- KW = 110 kW / HP = 150 Hp / Frame = 315S / Type = MC31S41300000 / 3 Phase Squirrel Cage Induction Motors. Learn Morewas ₹1,209,100.00 Special Price ₹395,471.00 -
-36%Fenner A18 Poly-F Plus PB Classical V Belts - 4 Pcs PackA V-belt is a flexible machine element used to transmit power between a set of grooved pulleys or sheaves. They are characterized as belts having a trapezium cross-section. V-belts are the most widely used belt drives since their geometry causes them to wedge tightly into the groove as the tension is increased. Other Specifications : Cord Material : Polyester Cord Neoprene Jacketed - Oil Resistance : Yes - Heat Resistance : Yes - Dimensions : Width = 1/2 Inches / Height = 5/16 Inches (13 mm / 8 mm) / Pitch Length = 490mm. --> FREE SHIPPING --> ₹ 491.00 + 18% = ₹ 579.00 Learn Morewas ₹772.00 Special Price ₹491.00 -
-36%Fenner A19 Poly-F Plus PB Classical V Belts - 4 Pcs PackA V-belt is a flexible machine element used to transmit power between a set of grooved pulleys or sheaves. They are characterized as belts having a trapezium cross-section. V-belts are the most widely used belt drives since their geometry causes them to wedge tightly into the groove as the tension is increased. Other Specifications : Cord Material : Polyester Cord Neoprene Jacketed - Oil Resistance : Yes - Heat Resistance : Yes - Dimensions : Width = 1/2 Inches / Height = 5/16 Inches (13 mm / 8 mm) / Pitch Length = 520mm. --> FREE SHIPPING --> ₹ 493.00 + 18% = ₹ 581.00 Learn Morewas ₹776.00 Special Price ₹493.00
Power Transmission
Filter
Shopping Options